Pipework may experience some changes also – low temperature heat pumps require a a higher level of water flow rate than boilers to operate efficiently that smaller pipes do not encourage. Larger pipes transfer heat effectively and efficiently at lower temperatures.
Heat pumps are a key element in the aim of national decarbonisation but can be problematic when installing. If a low temperature heat pump is installed into a domestic or commercial premise a noticeable amount of disruption will occur.
Many changes to the heating system will have to be made including the radiators, pipework and electrical upgrades. The radiators may have to be replaced as heat pumps operate at a lower flow temperature (between 35°C–55°C) than a traditional gas boiler that usually operate in between 60°C–75°C. To provide enough heat for the property new radiators may potentially have to be installed.
Pipework may experience some changes also – low temperature heat pumps require a a higher level of water flow rate than boilers to operate efficiently that smaller pipes do not encourage. Larger pipes transfer heat effectively and efficiently at lower temperatures.
Electrical upgrades will also be required if a normal temperature heat pump is installed. As the main source of power is transitioned from fossil fuels to electricity, a service panel that is only designed to operate at 100-amps will not be sufficient. Heat pumps require high voltage circuits when activated in cold weather.
High temperature heat pumps (HTHPs) do not demand any adaptations to radiators or pipework when retrofitting. Because high temperature heat pumps produce water that is heated at similar levels when compared to a gas boiler, at 55-80°C – no additional requirements exist to rip out radiators or replace pipework. The design of a high temperature heat pump means that an installation will work with existing infrastructure, not against.
When a high temperature heat pump is compared to a standard heat pump in terms of installation, a HTHP is less problematic, quicker and therefore reduces internal dust and material waste when retrofitting. Radiator and pipework compatibility means the HTHP can glide into operation once installed.
Rinnai R290 40kw and 50kw high-temperature air source heat pumps are the largest of this product range and ideal for DHW and heating projects. The R290 commercial air source heat pumps can be cascaded for greater heating and DHW output and is a market leading LOW-GWP heat pump that offer advanced controls.
The R290 high-temperature heat pumps supply hot water up to 75 degrees ensuring system and design flexibility. The Rinnai range of heat pump technology comes with a smart control system that features demand side response functionality which further future-proofs sustainability.
All R290 models have low noise capability making them suitable for areas with prohibitive sound legislation. The 40kw and 50kw air source heat pumps use R290 natural refrigerant gas which has a GWP (global warming potential) of three, ensuring that the Rinnai R290 high-temperature heat pump range is a sustainable and a future proof heating and DHW solution.
The 40kw and 50kw variants have a SCOP A+++ due to the increased efficiency achievable with the use of R290 refrigerant gas, meaning that the Rinnai range of high-temperature heat pumps is one of the most cost-effective and economical heating solutions available.
Rinnai recognises the importance of design support and system efficiency, to support this observation and customer commitment Rinnai utilise SPF (Seasonal Performance Factor), capital expenditure and operational expenditure to deliver your projects design towards the best possible solution. To take advantage of these services use our “help me choose” service today, By following this link Help me choose a product :: Rinnai UK (rinnai-uk.co.uk)
Rinnai also offers a range of products across a number of technological platforms and energies. Rinnai hybrid heat pump systems can accept clean electricity, natural gas and solar thermal. Rinnai Smart Systems can be programmed to switch fuels to maximise overall performance.
RINNAI OFFERS CLEAR PATHWAYS TO LOWER CARBON AND DECARBONISATION PLUS CUSTOMER COST REDUCTIONS FOR COMMERCIAL, DOMESTIC AND OFF-GRID HEATING & HOT WATER DELIVERY
www.rinnai-uk.co.uk/about-us/H3
- Rinnai’s range of decarbonising products – H1/H2/H3 – consists of hot water heating units in gas/BioLPG/DME, hydrogen ready units, electric instantaneous hot water heaters, electric storage cylinders and buffer vessels, a comprehensive range of heat pumps, solar, hydrogen-ready or natural gas in any configuration of hybrid formats for either residential or commercial applications. Rinnai’s H1/2/3 range of products and systems offer contractors, consultants and end users a range of efficient, robust and affordable low carbon/decarbonising appliances which create practical, economic and technically feasible solutions.
- Rinnai is a world leading manufacturer of hot water heaters and produces over two million units a year, operating on each of the five continents. The brand has gained an established reputation for producing products that offer high performance, cost efficiency and extended working lives.
- Rinnai products are UKCA certified, A-rated water efficiency, accessed through multiple fuel options and are available for purchase 24/7, 365 days a year. Any unit can be delivered to any UK site within 24 hours.
- Rinnai offer carbon and cost comparison services that will calculate financial, and carbon savings made when investing in a Rinnai system. Rinnai also provide a system design service that will suggest an appropriate system for the property in question.
- Rinnai offer comprehensive training courses and technical support in all aspects of the water heating industry including detailed CPD’s.
- The Rinnai range covers all forms of fuels and appliances currently available – electric, gas, hydrogen, BioLPG, DME solar thermal, low GWP heat pumps and electric water heaters More information can be found on Rinnai’s website and its “Help Me Choose” webpage.
RINNAI FULL PRODUCT AVAILABILITY 24/7 FOR NEXT DAY DELIVERY of ALL HOT WATER HEATING UNIT MODELS INCLUDING 48-58kW UNITS-
SAVINGS OF
20% REDUCTION of opex cost,
30% REDUCTION of initial cost
15% REDUCTION in carbon
75% REDUCTION of space
Visit www.rinnai-uk.co.uk
Or email engineer@rinaiuk.com
For more information on the RINNAI product range visit
www.rinnaiuk.com